Product news

  • Sensor Potting

    Sensors are potted in order to permanently protect electronic components from external influences such as heat, moisture, vibration, or chemical influences. ViscoTec dispensing pumps ensure high-precision, high-quality potting processes in the most diverse applications. In combination with the appropriate one or two-component potting materials for the respective application, perfect, customer-specific solutions are created. Depending on […]

  • Fully Automatic Filling Lines for Liquids

    The requirements for fully automated filling lines are diverse, but the following applies in all cases: Only an economical system is beneficial. High cycle rates and the required output rate with constantly precise dosing results must be met. This is a challenge, especially when dosing low to high viscosity liquids, and may create critical stages […]

  • Der neue Keramik-Rotor für die Baureihe RD-Dispenser von ViscoTec.

    ViscoTec Revolutionizes the Dispensing of Highly Abrasive Fluids

    ViscoTec opens a new chapter in dispensing highly abrasive fluids: By using a special coating on the rotors or more specifically by using a ceramic rotor, customers can achieve even greater process stability due to a much longer lifetime of the dispenser components. Increasing requirements in electronics manufacturing The ever smaller and more compact design […]

  • The syringes are filled by pressing the luer side against the dispenser. The unit dose are filled on the stopper side via mirror filling.

    Filling Composites in the Dental Industry

    In the dental industry, consumables such as composites are filled into disposable syringes with Luer Lock attachment or into smaller Unit Dose packages. These flowable filling materials made of plastic and glass are usually highly abrasive, highly viscous, and stringy. This places high demands on dosing and filling systems. The materials are used in the […]

  • Pre-filled Syringes prozesssicher abfüllen mit hochviskosen Fluiden und Pasten

    Filling of Semi-Solids in Ready-to-Fill Syringes

    Dosing syringes are an important option for the precise and clean application of pharmaceutical substances. However, the thin cylindrical cavities quickly become a challenge, especially when filling ready-to-fill syringes with highly viscous materials or semi-solids. Nevertheless, absolutely precise filling of the syringe is a must. Conventional filling technologies in the pharmaceutical industry often reach their […]

  • Rezirkulation im Pumpengehäuse wird ermöglicht durch zusätzlichen Umwälzstutzen

    Filling and Dosing without Sedimentation

    A major challenge for the dosing technology in food, cosmetics and pharmaceutical industries continues to be the gentle dosing of solids-laden liquids without damaging the solids. In addition, there is a risk that the solids will settle during prolonged downtimes. The material sediments. If this happens, the dosing unit becomes clogged and must be completely […]

  • Schublade mit

    Automated Management of Different Viscosities

    Wherever (vibration) energy has to be dissipated – i.e. where components move – dampers are often used to “buffer” this kinetic energy, e.g. using the viscous behaviour of liquids. The best example of the effect of large-volume dampers are structures embedded in bridge piers that compensate for earthquake vibrations using special hydraulic oil. Numerous examples […]

  • Waschmaschine, Mutter mit Kind

    Just the right dosage!

    How exactly should laundry detergent be dosed so that the laundry is completely clean, without the environment suffering? Does the dishwasher detergent compartment have to be filled completely in order to achieve streak-free cleanliness? But then it might not be possible to close the drawer properly? These are just a few of the questions that […]

  • Mehrfachabfüller Hygiene - für den Lebensmittel-, Pharma- und Kosmetikbereich

    Continuous Mixing and Filling of Viscous Materials

    With the introduction of the new ViscoDUO-VM HD, ViscoTec has become a pioneer in the dosing of two-component fluids and pastes in the hygienic sector. The new dosing system offers continuous mixing and dosing of two low to high viscosity materials with the same or different viscosities and guarantees precise, repeatable and process-safe mixing in […]

  • ViscoTec aerospace honeycomp potting 3M

    Aircraft Assembly: Great Potential for Automation

    Extensive, inaccurate and costly manual work, total waste of material: Up to now, many processes in aircraft construction have been carried out manually or only semi-automatically. This includes the filling of industrial hexagonal structures, so called “honeycombs”, which are essential for interior fittings. They form the core of the commonly used sandwich components. On the […]

  • Application bonding

    Microdispensing Systems for the Electronics Industry

    Microdispensing enables state-of-the-art manufacturing processes in the electronics industry and increases the service life of individual components. Adhesives, sealants, potting compounds or heat conductive pastes are processed in various applications. In consumer electronics in particular, the prerequisites for performance are increasing with ever smaller components and simultaneously falling manufacturing costs. Fully automatic and process-reliable microdispensing […]

  • Der neue Keramikrotor für die Baureihe RD-Dispenser von ViscoTec.

    Ceramic Rotor for RD Dispenser from ViscoTec

    For decades, ViscoTec has specialized in difficult dispensing applications within various industries. The dispensing technology specialist focuses its day-to-day optimizations of the product portfolio according to the needs of its customers. The proven stainless steel rotor has been further developed for the reliable dosing of abrasive fluids such as thermally conductive one- and two-component gap […]